Outdoor pedestals

Heads

Self-levelling head for PR and SE supports

Two-component PP and rubber tilting head that automatically compensates slopes up to 5%, with head-to-screw coupling preventing detachment.

Material: PP + anti-noise, anti-slip rubber
Sizes: Standard Ø 110 mm · XL Ø 150 mm
Tabs: 4 mm thick, H 12 mm (2 or 3 mm on request)
Slope: Up to 5%
Codes: E035101204 · E035201204 (XL)

Catalogue p. 24

Heads

Fixed head for NM supports

Two-component PP and rubber fixed head for New Maxi supports, with a head-to-screw coupling that keeps the head in its seat.

Material: PP + rubber
Sizes: Ø 110 mm · XL Ø 150 mm
Tabs: 4 mm thick, H 12 mm
Codes: E035011204 · E035061204 (XL)

Catalogue p. 24

Heads

Tilting head locking system

Insert that locks the tilting head of PR and SE supports, turning a self-levelling support into a fixed one; fits standard and XL heads.

Compatibility: PR and SE supports, standard or XL head
Size: Ø 38.5 mm, H 18 mm
Code: E036000100

Catalogue p. 24

Heads

Head for central support

Support placed at the centre of a slab to give the floor greater load capacity, adjusted by turning the base while holding the head.

Use: Slab centre, wall corner, along the wall or mid-floor
Adjustment: By rotating the base, no key needed

Catalogue p. 28

Adjustable supports

PR Prime® support

Pre-assembled adjustable pedestal with integrated extension and self-levelling Ø 110 mm head, covering 30–420 mm with three sizes.

Height: PR1 30–65 · PR2 65–155 · PR3 155–420 mm
Base: 300 cm² solid base with clip slots
Head: Self-levelling Ø 110 mm, slopes up to 5% (XL Ø 150 on request)
Codes: E500030065 · E500060155 · E500150420

Catalogue p. 40

Adjustable supports

PR extension for great heights

Extension fitted between the integrated extension and screw of PR3, with safety locks, for heights above 420 mm.

Heights: 595, 770 and 945 mm with one, two or three extensions
Compatibility: PR3 only
Code: E501000190

Catalogue p. 44

Adjustable supports

SE Eterno support

Adjustable pedestal with self-levelling tilting head compensating slopes up to 5%, adjustable from above with the key after laying.

Height: 28–550 mm (SE0–SE14, with P1 extensions)
Base: 320 cm² easy-break base
Temperature: −40 °C to +80 °C
Codes: E240028038–E240365550 · P1 extension E130125000

Catalogue p. 48

Adjustable supports

NM New Maxi support

Adjustable pedestal with fixed anti-noise rubber head and easy-break base; slopes are corrected with Twist slope compensators.

Height: 25–270 mm (NM1–NM5); up to 700 mm with PNM extensions
Base: 320 cm² easy-break base
Head: Ø 110 mm, 4 mm tabs H 12 mm
Codes: E014025047–E014150277 · PNM E044000145

Catalogue p. 54

Adjustable supports

SB Basic support

The simplest adjustable pedestal of the line, adjusted by turning the base, with a smooth 320 cm² base and water drainage.

Height: 27–120 mm (SB1–SB4); up to 300 mm with PSB extensions (SB5–SB8)
Base: 320 cm² smooth base
Slope: Twist TW 110 compensator
Codes: E015427035–E015481929 · PSB E044000625

Catalogue p. 60

Adjustable supports

Star.T support

Ultra-low adjustable support for renovations, 8 mm fixed top and 10–15 mm adjustment, raised in 5 mm steps with Star.T extensions.

Height: 10–15 mm; up to 30 mm with extensions
Extension: 5 mm, stackable
Slope: Twist TW 150 compensator
Codes: E003541115 · extension E003100025

Catalogue p. 66

Fixed height supports

EH Rubber 10+6 support

Fixed-height support in recyclable SBS rubber with sound-absorbing properties, usable whole, halved or in quarters.

Material: Recyclable SBS rubber
Height: 10 mm or 6 mm, Ø 120 mm
Tabs: 4 mm thick, H 10 mm (2–3 mm on request)
Codes: E000010004 · E000006004

Catalogue p. 76

Fixed height supports

EH 12 | 15 | 20 fixed height support

Stackable fixed-height supports, the quickest and most economical way to lay slabs on a raised system.

Height: 12, 15 or 20 mm (max. 3 stacked)
Tabs: 3 mm (EH12, EH15), 4 mm (EH20)
Variant: EH12 with 8 mm tabs for 20 mm self-supporting slabs
Codes: E008012008 · E000012003 · E000015000 · E002020000

Catalogue p. 80

Fixed height supports

Tilting balancer

Tilting insert for EH fixed supports that automatically levels small substrate imperfections, adding 5 mm to the height.

Height: 5 mm
Compatibility: EH fixed height supports
Code: E050005000

Catalogue p. 23

Fixed height supports

DM mini spacer for sand, grass and gravel

Small spacer for positioning slabs on sand, grass or gravel, supplied with a ground spike for anchoring, or without one for gravel.

Height: 60.5 mm with spike · 15.5 mm without
Width: 50.3 mm
Tabs: 4 mm, H 12 mm (2–3 mm on request)
Codes: E004000205 · E004000215

Catalogue p. 84

Fixed height supports

CR cross spacer for sand, grass and gravel

Polypropylene cross spacer, an alternative system for laying slabs on sand, grass or gravel.

Material: PP
Height: 15 or 20 mm
Tabs: 2, 3 or 4 mm
Codes: P021000052–P021000064

Catalogue p. 85

Special supports

SE W Eterno windproof system

SE support with XLW windproof head and stainless steel clips locking milled slab corners to the supports against wind uplift.

Height: 30–552 mm (SE W0–SE W14)
Head: Self-levelling XLW Ø 150 mm, 4 mm tabs H 14 mm
Slope: Up to 5%
Codes: E440030040–E440367552 · XLW head E035211204

Catalogue p. 88

Special supports

NM W New Maxi windproof system

NM support with fixed XLW windproof head accepting T or L stainless steel clips that hold slabs against wind suction.

Height: 30–275 mm (NM W1–NM W5)
Head: Fixed XLW Ø 150 mm, 4 mm tabs H 14 mm
Codes: E014030047–E014155277 · XLW head E035091204

Catalogue p. 90

Special supports

Windproof clips (T and L section)

Stainless steel clips inserted in the tabs of windproof heads to lock slabs milled at the four corners.

Material: Stainless steel
Types: T section · L section
Codes: Q200000310 · Q200000320

Catalogue p. 89

Special supports

SE S Eterno Silent support

Self-levelling SE support with PP + rubber head and 3 mm closed-cell foam under the base, reducing impact noise by over 25 dB.

Height: 31–553 mm (SES0–SES14)
Acoustic: ΔLw up to 25 dB (head), over 25 dB (base)
Base layer: 3 mm high-density closed-cell foam
Codes: E350031041–E350368553

Catalogue p. 94

Special supports

NM S New Maxi Silent support

New Maxi support with fixed bi-component head and 3 mm closed-cell foam layer under the base for impact-noise reduction.

Height: 28–273 mm (NMS1–NMS5)
Acoustic: Noise reduction over 25 dB
Base layer: 3 mm high-density closed-cell foam
Codes: E017028044–E017153274

Catalogue p. 96

Accessories

Adjustment key and screwdriver accessory

Reinforced key for adjusting PR, SE and NM supports from above on a finished floor, plus a steel screwdriver accessory for quick screwing.

Use: With standard 4 mm tabs only
Codes: E200250120 (key) · E200250130 (screwdriver accessory)

Catalogue p. 116

Accessories

Vertical lining clip

Pair of stainless steel clips over the head and under the base that hold a cut slab to close the vertical edge or form steps.

Material: Stainless steel
Slab thickness: 20, 30, 40 mm
Compatibility: PR, SE, NM, SB; Ø 110/150 mm heads
Codes: P021000322–P021000460

Catalogue p. 118

Accessories

Vertical angular lining clip

Angled head and base clips for vertical corner infill, replacing two head and two base clips with one of each.

Material: Stainless steel
Slab thickness: 20 mm
Codes: P021000972 · P021000982 · P021000912 · P021000922

Catalogue p. 120

Accessories

Perimeter spacer

Clip hooked onto the support head that keeps a 1 cm joint between the paving and perimeter walls without fixings through any waterproofing membrane turned up the wall.

Material: Stainless steel or PP
Joint: 10 ± 0.5 mm
Size: H 25.6 mm, L 161.6 mm
Codes: P021000220 · P021000230

Catalogue p. 122

Accessories

Supplementary rubber base

TPE rubber disc under the pedestal base that protects the waterproofing membrane and reduces impact-sound transmission.

Material: Thermoplastic rubber (TPE)
Size: Ø 215 mm, 2 mm thick
Code: E083000300

Catalogue p. 124

Accessories

Scudo separating layer

3 mm high-density closed-cell foam layer under the support base that protects the membrane and reduces impact noise.

Material: High-density modified closed-cell foam
Size: Ø 205 mm, 3 mm
Versions: Adhesive · non-adhesive
Codes: E083000233 · E083000223

Catalogue p. 125

Accessories

Slab lifter

Stainless steel tool inserted in the joint and turned 90° to lift an already laid slab.

Material: Stainless steel
Joints: 2, 3 and 4 mm
Code: M030000100

Catalogue p. 126

Accessories

Slab lifting handle

Handle with two lateral hooks inserted in the joints for laying new slabs or lifting laid ones.

Sizes: Adjustable 380–620 mm · fixed 400, 500, 600 mm
Codes: M030004060 · M030400400 · M030500500 · M030600600

Catalogue p. 127

Accessories

Suction cup slab lifter

Vacuum suction cup with 200 mm rubber pad and side seal for handling ceramic slabs on smooth or rough surfaces.

Size: Ø 200 mm
Capacity: Max. 110 kg
Code: M030100100

Catalogue p. 128

Accessories

Tool to increase the thickness of the tabs

Cap pushed onto the 4 mm spacer tabs to widen the joint while keeping the 12 mm tab height.

Thickness: 5, 6, 7, 8, 9, 10 mm
Codes: E004000305–E004000310

Catalogue p. 129

Accessories

Safety plate

Shaped 2 mm galvanised steel plate over the support heads that holds the slab and a person if a slab breaks.

Material: Galvanised steel, 2 mm
Size: 600 × 600 × 2 mm (others on request)
Height added: 3 mm
Codes: P021100060 · LGH1 shim E082001000

Catalogue p. 130

Accessories

Safety grid and DLG spacer

Interlocking 50 × 50 cm polymer panel on adjustable supports forming a sub-floor for stoneware, marble, stone or synthetic grass.

Material: Black thermoplastic polymer (PP)
Size: 500 × 500 mm, H 40 mm
Use: Outdoor only
Codes: P021305050 · DLG spacer E004002004

Catalogue p. 132

Accessories

Slab edge profile

Edge profile with a 30 mm decorative face and tooth that hides the junction between the raised floor and a vertical covering.

Material: Stainless steel or aluminium
Length: 1.20 m
Codes: P021200020 · P021200120

Catalogue p. 134

Accessories

Vertical perimeter profile

Aluminium profile closing the perimeter edges of raised floors with 20 mm slabs, with linear and 90° corner joints.

Material: Aluminium, silver or anthracite
Heights: 30, 60, 90, 120, 150 mm
Length: 2400 mm
Codes: P021241030–P021253150

Catalogue p. 135

Accessories

Rubber shims

Anti-slip, anti-noise rubber levellers placed on support heads to compensate 1–3 mm.

Material: Rubber
Sizes: LGH1/2/3: 1, 2, 3 mm, Ø 110 mm · LH3: 3 mm, Ø 150 mm
Codes: E082001000–E082003000 · E081003000

Catalogue p. 138

Accessories

Twist slope compensator

Rotating compensator on NM, SB, ST and EH heads giving 0–1% slope correction each; several can be combined.

Slope: 0–1% per compensator, cumulative
Sizes: TW 110 Ø 110 mm · TW 150 Ø 150 mm
Codes: E084000110 · E084000150

Catalogue p. 139

Accessories

Clip for hexagonal slabs

Small polypropylene spacer clip fitted on PR, SE and NM heads for laying hexagonal slabs.

Material: PP
Tabs: 2, 3 or 4 mm
Codes: E004001002–E004001004 · heads E035100040, E035400040

Catalogue p. 142

Every product in this range

Self-levelling head for PR and SE supports

Fixed head for NM supports

Tilting head locking system

Head for central support

PR Prime® support

PR extension for great heights

SE Eterno support

NM New Maxi support

SB Basic support

Star.T support

EH Rubber 10+6 support

EH 12 | 15 | 20 fixed height support

Tilting balancer

DM mini spacer for sand, grass and gravel

CR cross spacer for sand, grass and gravel

SE W Eterno windproof system

NM W New Maxi windproof system

Windproof clips (T and L section)

SE S Eterno Silent support

NM S New Maxi Silent support

Adjustment key and screwdriver accessory

Vertical lining clip

Vertical angular lining clip

Perimeter spacer

Supplementary rubber base

Scudo separating layer

Slab lifter

Slab lifting handle

Suction cup slab lifter

Tool to increase the thickness of the tabs

Safety plate

Safety grid and DLG spacer

Slab edge profile

Vertical perimeter profile

Rubber shims

Twist slope compensator

Clip for hexagonal slabs

Raised access flooring

Have a project in design or at tender?